Request Service

 

We've come across this great article on Tools You Need to Install a New Bathtub directly below on the internet and think it made sense to write about it with you on this site.

Installing a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult project. If the old tub is easily obtainable, the job can move easily; if you have to open up a wall surface to eliminate the old tub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and also set in the brand-new one. Ensure you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is far better to take into consideration employing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your restroom if you have already gotten a new tub and do not require to transform the plan of your previous water system pipes.
Your devices and material checklist need to make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Setup

First of all, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to stop pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last placement.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bathtub

Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bathtub until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water supply and examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub must wait till the bathtub has actually been made use of at the very least once as this will resolve it right into its last setting.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Protect the tap in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The previous kind ought to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, triggering the water to permeate the wall between the bathroom as well as the tiling, bring about difficulties with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components and fittings. They are sold in tubes as well as cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water-proof glue and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I found that piece on How to Install a Bathtub while browsing the search engines. If you liked our article please do not forget to share it. Thank you so much for going through it.

We're alert, ring!